Introduction to Microwave Waveguide Flanges
A waveguide flange is a connector for joining sections of waveguide, and is essentially the same as a pipe flange—a waveguide, in the context of this article, being a hollow metal conduit for microwave energy. The connecting face of the flange is either square, circular or (particularly for large or reduced-height rectangular waveguides), rectangular. The connection between a pair of flanges is usually made with four or more bolts, though alternative mechanisms, such as a threaded collar, may be used where there is a need for rapid assembly and disassembly. Dowel pins are sometimes used in addition to bolts, to ensure accurate alignment, particularly for very small waveguides where higher accuracy is required for higher frequencies.
Key features of a waveguide join are; whether or not it is air-tight, allowing the waveguide to be pressurized, and whether it is a contact or a choke connection. This leads to three sorts of flange for each size of rectangular waveguide.
For rectangular waveguides there exist a number of competing standard flanges which are not entirely mutually compatible. Standard flange designs also exist for double-ridge, reduced-height, square and circular waveguides.
Unpressurised and Pressurised Waveguide Flanges
The atmosphere within waveguide assemblies is often pressurized, either to prevent the ingress of moisture, or to raise the breakdown voltage in the guide and hence increase the power that it can carry. Pressurization requires that all joints in the waveguide be airtight. This is usually achieved by means of a rubber O-ring seated in a groove in the face of at least one of flanges forming each join. Gasket, gasket/cover or pressurizable flanges (such as that on the right of figure 2), are identifiable by the single circular groove which accommodates the O-ring. It is only necessary for one of the flanges in each pressurizable connection to be of this type; the other may have a plain flat face (like that in figure 1). This ungrooved type is known as a cover, plain or unpressurizable flange.
It is also possible to form air-tight seal between a pair of otherwise unpressurizable flanges using a flat gasket made out of a special electrically conductive elastomer. Two plain cover flanges may be mated without such a gasket, but the connection is then not pressurizable.
Electric current flows on the inside surface of the waveguides, and must cross the join between them if microwave power is to pass through the connection without reflection or loss.
Microwave Flange Standards
International Electrotechnical Commission (IEC) standard IEC 60154 describes flanges for square and circular waveguides, as well as for what it refers to as flat, medium-flat, and ordinary rectangular guides. IEC flanges are identified by an alphanumeric code consisting of; the letter U, P or C for Unpressurizable (plain cover), Pressurizable (with a gasket groove) and Choke (with both choke gasket grooves); a second letter, indicating the shape and other details of the flange and finally the IEC identifier for the waveguide. For standard rectangular waveguide the second letter is A to E, where A and C are round flanges, B is square and D and E are rectangular. So for example UBR220 is a square plain cover flange for R220 waveguide (that is, for WG20, WR42), PDR84 is a rectangular gasket flange for R84 waveguide (WG15, WR112) and CAR70 is a round choke flange for R70 waveguide (WG14, WR137).
MIL-DTL-3922 is a United States Military Standard giving detailed descriptions of choke, gasket/cover and cover flanges for rectangular waveguide. MIL_DTL-39000/3 describes flanges for double-ridge waveguide, and formerly also for single-ridge guide. MIL-Spec flanges have designations of the form UG-xxxx/U where the x’s represent a variable-length catalogue number, not in itself containing any information about the flange.
The Electronic Industries Alliance (EIA) is the body that defined the WR designations for standard rectangular waveguides. EIA flanges are designated CMR (for Connector, Miniature, Rectangular waveguide) or CPR (Connector, Pressurizable, Rectangular waveguide) followed by the EIA number (WR number) for the relevant waveguide. So for example, CPR112 is a gasket flange for waveguide WR112 (WG15).
The Radio Components Standardization Committee (RCSC) is the body that originated the WG designations for standard rectangular waveguides. It also defined standard choke and cover flanges with identifiers of the form 5985-99-xxx-xxxx where the x’s represent a catalogue number, not in itself containing any information about the flange.
What is a Waveguide?
A waveguide is an electromagnetic feed line that is used for high frequency signals. Waveguides conduct microwave energy at lower loss than coaxial cables and are used in microwave communications, radars and other high frequency applications.
The waveguide must have a certain minimum cross section, relative to the wavelength of the signal to function properly. If wavelength of the signal is too long (Frequency is too low) when compared to the cross section of the waveguide, the electromagnetic fields cannot propagate. The lowest frequency range at which a waveguide will operate is where the cross section is large enough to fit one complete wavelength of the signal.
For Further Information
For More Information on Microwave Planning, Please Contact Us
You must be logged in to post a comment.